Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to simultaneously stream data between two devices on one BLE connection 0

GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
1460 views

0 replies

Started over 10 years ago
by user7512
Not Answered

Is NRF Beacon Kit compatible with S130? 0

Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...

501 views

0 replies

Started over 10 years ago
by user8359
Not Answered
about nrf24le1debug problem 0

hi: now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
- 24le1 debug
437 views

0 replies

Started over 10 years ago
by user6832
Not Answered

Communication timeout. Emulator did not re-enumerate 0

This is what I got after upgrading my nRF51 dongle firmware. It always times out. I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...

1585 views

0 replies

Started over 10 years ago
by user3033
Not Answered
APP which support to conect 8 or more BLE peripherals 0

Hi all, Good day. Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time. Thanks & Regards Jenson
- bluetooth low energy
417 views

0 replies

Started over 10 years ago
by user8311

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software and Protocols: Field verification of the GNSS

user87864

Introduction Intention of this guide is to clarify and describe main aspects relevant for nRF9160 GNSS receiver functionality, build configurations, tool recommendations and how to get started with the…
- 10 Jun 2022
Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

user2133

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

user27011

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

user27011

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

user17370

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022