Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to simultaneously stream data between two devices on one BLE connection 0

GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
1460 views

0 replies

Started over 10 years ago
by user7512
Not Answered

Is NRF Beacon Kit compatible with S130? 0

Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...

501 views

0 replies

Started over 10 years ago
by user8359
Not Answered
about nrf24le1debug problem 0

hi: now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
- 24le1 debug
437 views

0 replies

Started over 10 years ago
by user6832
Not Answered

Communication timeout. Emulator did not re-enumerate 0

This is what I got after upgrading my nRF51 dongle firmware. It always times out. I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...

1585 views

0 replies

Started over 10 years ago
by user3033
Not Answered
APP which support to conect 8 or more BLE peripherals 0

Hi all, Good day. Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time. Thanks & Regards Jenson
- bluetooth low energy
417 views

0 replies

Started over 10 years ago
by user8311

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Hardware design, test and measurement: nRF52832 Specific PCB Guidelines

user9102

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

user2124

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

user89293

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Hardware design, RF test and coverage: Using nRF9160 against R&S CMW500 (or CMW290) in signalling callbox mode

user89029

This blog clarifies what are the basic requirements when nRF9160 is used in signalling/RF testing against R&S CMW290/500 test setups. Setting up: The RF attenuations can be modified from RF settings->RF…
- 31 Mar 2020
Bluetooth low energy: Mocking CoreBluetooth

user3284

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

user24652

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020