Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF51xxx debugging with BDI debugger 0

I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...

436 views

0 replies

Started over 10 years ago
by user8280
Not Answered

Scaner Design uisng nRF24L01 0

hi, I want to scan ism band to detect active nRF24L01 transmitters. How much time receiver will take to scan the whole band.?

573 views

0 replies

Started over 10 years ago
by user8259
Not Answered

Writing data using Python binding method 0

Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...

533 views

0 replies

Started over 10 years ago
by user8232
Not Answered

Can anyone explain ble event in Python? 0

Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...

411 views

0 replies

Started over 10 years ago
by user8232
Not Answered

pstorage_store doesn't call callback 0

pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...

390 views

0 replies

Started over 10 years ago
by user7609

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software and Protocols: How to connect nRF9160 DK to Google Cloud

user92402

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

user17370

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

user2982

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

user73423

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Hardware design, RF test and coverage: Measuring PSM idle current on the nRF91 DK

Stian Røed Hafskjold

New updated guide can be found here: Getting started with current measurements on the nRF9160 Or Please follow the official documentation when using v1.0.0 of the DK: - Prepare the board for measureme…
- 28 May 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

user73423

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019