Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF51xxx debugging with BDI debugger 0

I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...

436 views

0 replies

Started over 10 years ago
by user8280
Not Answered

Scaner Design uisng nRF24L01 0

hi, I want to scan ism band to detect active nRF24L01 transmitters. How much time receiver will take to scan the whole band.?

573 views

0 replies

Started over 10 years ago
by user8259
Not Answered

Writing data using Python binding method 0

Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...

533 views

0 replies

Started over 10 years ago
by user8232
Not Answered

Can anyone explain ble event in Python? 0

Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...

411 views

0 replies

Started over 10 years ago
by user8232
Not Answered

pstorage_store doesn't call callback 0

pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...

390 views

0 replies

Started over 10 years ago
by user7609

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Hardware design, test and measurement: nRF52832 Specific PCB Guidelines

user9102

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

user2124

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

user89293

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Hardware design, RF test and coverage: Using nRF9160 against R&S CMW500 (or CMW290) in signalling callbox mode

user89029

This blog clarifies what are the basic requirements when nRF9160 is used in signalling/RF testing against R&S CMW290/500 test setups. Setting up: The RF attenuations can be modified from RF settings->RF…
- 31 Mar 2020
Bluetooth low energy: Mocking CoreBluetooth

user3284

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

user24652

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020