Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
stackpointer after start from SD V8.0 0

Hello, i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine. Now i switch to the new SD V8.0. The SD V8.0 is programming with...
- d110 nrf51822 sd110_v8.0 gcc
401 views

0 replies

Started over 10 years ago
by user8001
Not Answered
NRF51822 S110 proximity example does not work for IPhone6? 0

Hi everyone, I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
- s110
- iphone6
- nrf51822
1725 views

0 replies

Started over 10 years ago
by user7995
Not Answered

Can't read rssi value when when device alarming used IAS 0

Hi,all.i use ios to read rssi value from device after write 0x01 to IAS services.Can someone help me?

393 views

0 replies

Started over 10 years ago
by user6514
Not Answered

Serial Bootloader for NRF24LE1 0

I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory. My...

498 views

0 replies

Started over 10 years ago
by user7668
Not Answered
Unable to debug with Eclipse nRF51822 chip 0

Hi, I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
- problem
- eclipse
- s110
- ramon
- debug
- no source available for
- nrf51822
784 views

0 replies

Started over 10 years ago
by user7922

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015