Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

ubuntu14.4 connect fail with nRF51 keypad demo 0

I try to use hcidump, capture CSR dongle on ubuntu14.4. I can find SDK8.1.1 s110 keypad demo create connection fail. HCI Event: Command Complete (0x0e) plen 4 LE Set...

422 views

0 replies

Started over 10 years ago
by user7299
Not Answered

nRF51822 firmware 0

I want to experiment with recording observations of the beacons with raspberry pi's. Is there any precompiled firmware I can install on the nRF51822 smart beacon...

377 views

0 replies

Started over 10 years ago
by user7387
Not Answered
NRF24L01+ not receiving anything 0

Hello everyone, I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers. My SPI communication is working fine as I am able to write and...
- nrf24l01
2113 views

0 replies

Started over 10 years ago
by user7272
Not Answered

TinyDTLS for the IoT SDK, CCM Mode Error 0

Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...

610 views

0 replies

Started over 10 years ago
by user3665
Not Answered
nRF8001 latency between data received and RDYN is low 0

Hi, I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
- nrf8001
326 views

0 replies

Started over 10 years ago
by user4479

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015