Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SPI Multiple Masters 0

Hello, I am tryong to use to masters to communicate with two accelerometers. Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
- spi
- multiple master and slave
2055 views

0 replies

Started over 11 years ago
by user6769
Not Answered

Power-fail NVMC protection 0

In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...

381 views

0 replies

Started over 11 years ago
by user5810
Not Answered
Unable to check anything on hyperterminal or teraterm. How to check it? 0

Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
528 views

0 replies

Started over 11 years ago
by user6285
Not Answered

nrf905 Data loss 0

Hi,my friend, Now,I use nrf905.Situation is as follows: I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data. 1.The Product host is to use the stick...

258 views

0 replies

Started over 11 years ago
by user7057
Not Answered
Writing peripheral characteristic value 0

Hello, I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
- value
- bluetooth low energy
- keil
- write
- nrf51822
- characteristic
2252 views

0 replies

Started over 11 years ago
by user7021

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

user2982

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

user8636

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015