Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
BLE Mesh LED onoff example issue 0

I use the LED onoff example of the Nordic BLE Mesh template (Version : 5.0), using two nodes (One Client, One Server). The nodes are already Provisioned. I want to know...
26 views

0 replies

Started over 4 years ago
by user110331
Not Answered
nRF52820 Bootloader error! (Part of the HEX regions are out of the device memory size ,but you can still proceed write operation) 0

Hello, I am a firmware engineer in taiwan. I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
13 views

0 replies

Started over 4 years ago
by user117023
Not Answered
delay after SPIS uninit 0

Hi, Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used. Problem is the delay that is needed after nrfx_spis_uninit call...
13 views

0 replies

Started over 4 years ago
by user30023
Not Answered
Need ADC sample code with Bluetooth communication (NRF52840) 0

Hi, I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
- development
- software
- beacons
- nrf52840
65 views

0 replies

Started over 4 years ago
by user115289
Not Answered
nrf52832 not hop and disconnection from android 7 system 0

1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ? 2) nrf52832...
16 views

0 replies

Started over 4 years ago
by user117025

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

user82532

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

user27011

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

user7571

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015