Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
BLE Mesh LED onoff example issue 0

I use the LED onoff example of the Nordic BLE Mesh template (Version : 5.0), using two nodes (One Client, One Server). The nodes are already Provisioned. I want to know...
26 views

0 replies

Started over 4 years ago
by user110331
Not Answered
nRF52820 Bootloader error! (Part of the HEX regions are out of the device memory size ,but you can still proceed write operation) 0

Hello, I am a firmware engineer in taiwan. I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
13 views

0 replies

Started over 4 years ago
by user117023
Not Answered
delay after SPIS uninit 0

Hi, Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used. Problem is the delay that is needed after nrfx_spis_uninit call...
13 views

0 replies

Started over 4 years ago
by user30023
Not Answered
Need ADC sample code with Bluetooth communication (NRF52840) 0

Hi, I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
- development
- software
- beacons
- nrf52840
65 views

0 replies

Started over 4 years ago
by user115289
Not Answered
nrf52832 not hop and disconnection from android 7 system 0

1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ? 2) nrf52832...
16 views

0 replies

Started over 4 years ago
by user117025

Recent in Nordic blog

One minute to understand BLE connection data package

user67053

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

user67053

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

user12165

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017

Latest guides

Hardware design, test and measurement: nRF52832 Specific PCB Guidelines

user9102

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

user2124

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

user89293

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Hardware design, RF test and coverage: Using nRF9160 against R&S CMW500 (or CMW290) in signalling callbox mode

user89029

This blog clarifies what are the basic requirements when nRF9160 is used in signalling/RF testing against R&S CMW290/500 test setups. Setting up: The RF attenuations can be modified from RF settings->RF…
- 31 Mar 2020
Bluetooth low energy: Mocking CoreBluetooth

user3284

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

user24652

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020