Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Debugging gets stuck at INLINE app_timer_evt_get() 0

I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
- 110 nrf51822 timer
458 views

0 replies

Started over 11 years ago
by user4813
Not Answered

DFU can not complete 0

Hi, Recently, the DFU of the "Master Control Panel" (Android) can not complete the upload mission. But, the DFU of the nRF-Toolbox in iOS is work well. Old...

354 views

0 replies

Started over 11 years ago
by user2922
Not Answered
iOS nRF Toolbox 1.5/1.6 doesn't send long init packet 0

I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets. I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
639 views

0 replies

Started over 11 years ago
by user3848
Not Answered
Can BLE and SoC events cause SD_EVT_IRQn simultaneously? 0

Hello everybody, In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
- event
- irq
- s110
- ble event
- oftdevice
- soc event
- interrupt
- isr
- nrf51822
961 views

0 replies

Started over 11 years ago
by user3267
Not Answered
Assembly Code in SDK 7.2 DFU 0

Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c. I found that the offset in line: LDR R0, [R1, #24] always...
- bootloader dfu
819 views

0 replies

Started over 11 years ago
by user5873

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

user2982

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

user8636

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015