Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

ADC reference 0

Hi, could you please tell me if my assumptions below correct? Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...

1354 views

0 replies

Started over 11 years ago
by user4482
Not Answered
Odd behavior with SOFTDEVICE_HANDLER_INIT w/o Scheduler 0

When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz The project I based...
746 views

0 replies

Started over 11 years ago
by user4813
Not Answered

API to see undiscoverable mode 0

I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...

787 views

0 replies

Started over 11 years ago
by user3579
Not Answered
ADC for battery measurment and ports 26,27 and 28 0

Hi, I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end). I am also reading several ports...
- adc
- s110
- nrf51822
691 views

0 replies

Started over 11 years ago
by user3231
Not Answered
User data cannot be preserved in FLASH on PCA10001? 0

Hi, I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
- pstorage
- s110
- nrf51822
342 views

0 replies

Started over 11 years ago
by user4448

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

user82532

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

user27011

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

user7571

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015