Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

ADC reference 0

Hi, could you please tell me if my assumptions below correct? Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...

1354 views

0 replies

Started over 11 years ago
by user4482
Not Answered
Odd behavior with SOFTDEVICE_HANDLER_INIT w/o Scheduler 0

When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz The project I based...
746 views

0 replies

Started over 11 years ago
by user4813
Not Answered

API to see undiscoverable mode 0

I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...

787 views

0 replies

Started over 11 years ago
by user3579
Not Answered
ADC for battery measurment and ports 26,27 and 28 0

Hi, I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end). I am also reading several ports...
- adc
- s110
- nrf51822
691 views

0 replies

Started over 11 years ago
by user3231
Not Answered
User data cannot be preserved in FLASH on PCA10001? 0

Hi, I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
- pstorage
- s110
- nrf51822
342 views

0 replies

Started over 11 years ago
by user4448

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

user7328

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

user25682

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

user6207

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

user72692

Check out older versions of this tutorial: nRF Connect SDK Tutorial series - Part 0 | NCS v1.2.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.3.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1…
- 24 May 2019
Hardware design, RF test and coverage: External GPS antenna on nRF9160 DK

user17630

The nRF9160 DK comes with an on-board antenna for GPS, but on some boards this antenna is not functional on board versions up to and including v0.8.2 due to this errata. It can also be very practical to…
- 24 May 2019
Getting started: How to get modem trace using “Trace Collector” in nRF Connect

user2124

UPDATE MAY 2021:Please follow the official documentation in infocenter. The following information is deprecated, please follow the documentation link at the top. Trace Collector app collects UART traces…
- 30 Apr 2019
Getting started: Store dust sensor data on nRF Connect for Cloud

user24652

In this example we are using the nRF Connect for Cloud Device API, which is a free service for protyping IoT products and is built on top of AWS IoT, to store dust sensor readings. The API is device-agnostic…
- 12 Mar 2019
Mesh Networks: Provisioning and running Nordic's BLE Mesh with Python Application Controller Interface (PyACI)

user17370

Purpose This document will explain the Mesh Demo and the motivations behind the design decisions. Please find attached PDF file at the bottom of this tutorial for high-resolution version of this tutorial…
- 3 Feb 2019
Getting Started : Using GDB with Nordic devices

user4528

The GNU Debugger (GDB) is a popular tool that provides familiar features like breakpoints along with a command syntax that allows creativity in the debugging process. Although its command line interface…
- 31 Jan 2019