Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

DFU-OTA with S110 v7a3 and nRFToolBox on iPhone 5S 0

Hi Guys, since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following: s110_nrf51822_7...

678 views

0 replies

Started over 12 years ago
by user3337
Not Answered
relation in channel and pin 0

Hi All, i would like to know about 1) what is channel in nrf51288? 2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs example channel...
367 views

0 replies

Started over 12 years ago
by user4125
Not Answered
uart(with USB to UART bridge) dfu can not work 0

Hi, I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
- dfu with hci
676 views

0 replies

Started over 12 years ago
by user2776
Not Answered
Re-connecting iOS(ANCS) takes about 20 sec. 0

Hi. I have been trying get a notification through ANCS. I have created an app which is made by modifying ble_app_ancs sample. It works basically but there is one problem...
- s110
- nrf51822
557 views

0 replies

Started over 12 years ago
by user4162
Not Answered

Consuming too much power in search mode 0

Hello, I'm using the nrf51422 with 210 softdevice. I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...

449 views

0 replies

Started over 12 years ago
by user3803

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015