Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
related to threads 0

Hi all, i want to establish connection between two threads in cmsis-rtos, can i use 1) semaphore to do this? 2)message queue should be used or any other ipcs can be...
704 views

0 replies

Started over 12 years ago
by user4125
Not Answered

Data transfer rate by serialization 0

Hi, I have two CPU in our product. (STM32F2 and Nordic nrf51422). I use serialization function to link those two CPU(refer to ble_s110_serialization sample) But I find...

521 views

0 replies

Started over 12 years ago
by user2920
Not Answered

Can't connect directly after I exit our app by back key on phone 0

Hi, My behavior is as follows Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic) Turn on my cell phone(Samsung Note3),scan my device...

302 views

0 replies

Started over 12 years ago
by user2920
Not Answered

Why do I use twi_hw_master.c can run on 2.4G, Bluetooth can not? 0

Hello: I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...

840 views

0 replies

Started over 12 years ago
by user3262
Not Answered
nRF51822 and nRF24L01+ 0

Hello! How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
- nrf51822 nrf24l01+ addre
575 views

0 replies

Started over 12 years ago
by user4158

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015