Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Best way to minimize NRF_ANT_ERROR_TRANSFER_IN_PROGRESS 0

What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
- softdevice
- ant
452 views

0 replies

Started over 12 years ago
by user2675
Not Answered

nRF24L01+ transmitting before auto acknowledgement is complete. 0

I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...

1184 views

0 replies

Started over 12 years ago
by user3852
Not Answered
Connect another board over UART from nRF51822 mKit board 0

I am using mbed library to get leg up on development. This is the first time I am writing any MCU application and it sure makes things a lot easier. I am using nRF51822...
- mbed
- uart
- nrf51822
1120 views

0 replies

Started over 12 years ago
by user3642
Not Answered
HID Service on iOS 0

I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
1617 views

0 replies

Started over 12 years ago
by user2147
Not Answered

the speed of large amount of data 0

int main(void) { uint32_t BufferCount; uint32_t err_code; // Initialize leds_init(); timers_init(); buttons_init(); uart_init(); ble_stack_init(); gap_params_init...

714 views

0 replies

Started over 12 years ago
by user3821

Recent in Nordic blog

Nordic Semiconductor nRF51822 Firmware for Background Data Recording

user4448

#Nordic Semiconductor nRF51822 Firmware for Background Data Recording Updating on https://github.com/scytulip/nrf51-back-rec Design Objective This firmware is designed for low-cost long-time low-power…
- 23 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

user4711

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

user4711

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014

Latest guides

Software and Protocols: Field verification of the GNSS

user87864

Introduction Intention of this guide is to clarify and describe main aspects relevant for nRF9160 GNSS receiver functionality, build configurations, tool recommendations and how to get started with the…
- 10 Jun 2022
Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

user2133

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

user27011

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

user27011

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

user17370

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022