Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Archiving 32kbps throughput using codedPHY for above 200m range (nRF52840) 0

Hello, I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below: ATT MTU: 247 Data length: 27 Connection...
33 views

0 replies

Started over 4 years ago
by user116246
Not Answered
Write long characteristics 0

Team, I am using nrf52810, sdk 17, sd112. I have setup a write characteristics, to receive some long data ( 64 bytes) // write char memset(&add_char_params, 0, sizeof...
37 views

0 replies

Started over 4 years ago
by user101381
Not Answered
BLE Characteristic Read By Connected Client 0

Hello, I have a BLE peripheral device that becomes the server once a connection is established. The BLE services and characteristics are all custom, I will include the defines...
36 views

0 replies

Started over 4 years ago
by user64801
Not Answered
Help with basic implementation of UART 0

Hello, I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
40 views

0 replies

Started over 4 years ago
by user116076
Not Answered
PIN_CNF Sense change state 0

Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
27 views

0 replies

Started over 4 years ago
by user74012

Recent in Nordic blog

nRF52 Range Extension with RFaxis' RFX2411N

user9022

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

user7627

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

user7377

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015