Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

408 views

0 replies

Started over 12 years ago
by user3476
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1010 views

0 replies

Started over 12 years ago
by user3653
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
935 views

0 replies

Started over 12 years ago
by user3583
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

814 views

0 replies

Started over 12 years ago
by user3506
Not Answered
Bonds/pStorage with fast connection interval 0

I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
- ancs
- pstorage
- timing
- softdevice
- bond manager
614 views

0 replies

Started over 12 years ago
by user2596

Recent in Nordic blog

The KEY POINT of example "ble_app_uart"

user66980

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017
Introduce smart motion controller - ELIO

user8948

"ELIO" is a Bluetooth module and smartphone application that can drive motor(DC, Servo) and illuminate LEDs. This module mounts Nordic's nRF52832 and motor controller IC. Smartphone application can create…
- 12 Dec 2017
Programming and debugging custom nRF5x devices

user3126

Programming and debugging the nRF5x on our Developments kits is straight forward. Doing the same when you are using other boards might not be so easy. In this blog post we will explain which components…
- 8 Dec 2017

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015