Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF51822 compile environment 0

Hi, Can I use RVDS to develop our project on nRF51822? And How can I get the reference code on RVDS? Thank you

376 views

0 replies

Started over 12 years ago
by user2987
Not Answered

DFU with IAR IDE 0

Hi, I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...

824 views

0 replies

Started over 12 years ago
by user3381
Not Answered

S110 7.0.0 : Can I write my own MBR? 0

Hi I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...

1316 views

0 replies

Started over 12 years ago
by user2241
Not Answered

S110 v7.0.0-2.alpha and sd_softdevice_forward_to_application() 0

Hi S110 v7.0.0-2.alpha got released today. In the release notes it says... [b]The SoftDevice can now be configured to forward interrupts to one of several applications...

647 views

0 replies

Started over 12 years ago
by user2241
Not Answered

bulk/block data transfer 0

Does your new implemenation of BLE 4.1 support bulk/block data transfer? What data rate could be possible ? /Best Regards Kjell Bystedt

653 views

0 replies

Started over 12 years ago
by user2993

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015