Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Performance of GATT 0

Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
- performance
- speed
- uart
- nrf51822
851 views

0 replies

Started over 12 years ago
by user2574
Not Answered

Is there any ble eample in nRF51 SDK can used with IOS? 0

If it can work with iOS blue setting will be better I need some reference to dev hid device in IOS but I can just find my device ,connect ok but not work.

314 views

0 replies

Started over 12 years ago
by user2770
Not Answered

Q about APP_TIMER_MIN_TIMEOUT_TICKS 0

I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...

726 views

0 replies

Started over 12 years ago
by user3131
Not Answered

nrftoolbox dfu application error 0

Hi, While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently. I use latest version...

600 views

0 replies

Started over 12 years ago
by user2463
Not Answered

Stopping app_timer (using app_timer_stop) results in too much current during ON,IDLE mode 0

I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following: Initializes the app_timer using the scheduler: ...

1170 views

0 replies

Started over 12 years ago
by user3119

Recent in Nordic blog

Allowing debugger access to nRF5340

user4528

After an nRF5340 executes a power-on, brown-out, watchdog timer, or pin reset it is not automatically accessible to debug probes. This is true even if the nRF5340's memory is completely blank --i.e. no…
- 15 Jan 2021
Connected Home over IP: Sneak peek of early development on nRF52840

user5630

This blog post provides step-by-step instruction on running Door Lock example from the CHIP repository. It demonstrates how with help of the mobile phone, commission accessory to the network using Bluetooth…
- 28 Dec 2020
FruityMesh v1.0 - connection-based open source BLE Mesh now available on Github

user5300

Hello everyone, 5 years ago, FruityMesh was open sourced as the first connection-based Bluetooth Low Energy mesh network based on the nRF52 series. Now, after constant development at our Mway headquarter…
- 17 Dec 2020

Latest guides

Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

user72692

Check out older versions of this tutorial: nRF Connect SDK Tutorial series - Part 0 | NCS v1.2.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.3.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1…
- 24 May 2019
Hardware design, RF test and coverage: External GPS antenna on nRF9160 DK

user17630

The nRF9160 DK comes with an on-board antenna for GPS, but on some boards this antenna is not functional on board versions up to and including v0.8.2 due to this errata. It can also be very practical to…
- 24 May 2019
Getting started: How to get modem trace using “Trace Collector” in nRF Connect

user2124

UPDATE MAY 2021:Please follow the official documentation in infocenter. The following information is deprecated, please follow the documentation link at the top. Trace Collector app collects UART traces…
- 30 Apr 2019
Getting started: Store dust sensor data on nRF Connect for Cloud

user24652

In this example we are using the nRF Connect for Cloud Device API, which is a free service for protyping IoT products and is built on top of AWS IoT, to store dust sensor readings. The API is device-agnostic…
- 12 Mar 2019
Mesh Networks: Provisioning and running Nordic's BLE Mesh with Python Application Controller Interface (PyACI)

user17370

Purpose This document will explain the Mesh Demo and the motivations behind the design decisions. Please find attached PDF file at the bottom of this tutorial for high-resolution version of this tutorial…
- 3 Feb 2019
Getting Started : Using GDB with Nordic devices

user4528

The GNU Debugger (GDB) is a popular tool that provides familiar features like breakpoints along with a command syntax that allows creativity in the debugging process. Although its command line interface…
- 31 Jan 2019