Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Control GPIO by PPI and timer1 +1

I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000. I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...

1388 views

0 replies

Started over 12 years ago
by user2697
Not Answered

One command execution time on serialization 0

Hi, I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...

481 views

0 replies

Started over 12 years ago
by user2920
Not Answered

get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE 0

I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...

2118 views

0 replies

Started over 12 years ago
by user3506
Not Answered

HOW do I erase SDK5.2 version of flash and read not, in SDK4.2 can. 0

Hello: Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...

1007 views

0 replies

Started over 12 years ago
by user3262
Not Answered

nRF24LU1 programs a byte through spi command,a strange problem occured... 0

before i write the flash, it has been erased.so ,its value is all 0xff. when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...

421 views

0 replies

Started over 12 years ago
by user3353

Recent in Nordic blog

Thingy:52 MOSFET Usage

user5263

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

user27011

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015