Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Control GPIO by PPI and timer1 +1

I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000. I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...

1388 views

0 replies

Started over 12 years ago
by user2697
Not Answered

One command execution time on serialization 0

Hi, I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...

481 views

0 replies

Started over 12 years ago
by user2920
Not Answered

get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE 0

I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...

2118 views

0 replies

Started over 12 years ago
by user3506
Not Answered

HOW do I erase SDK5.2 version of flash and read not, in SDK4.2 can. 0

Hello: Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...

1007 views

0 replies

Started over 12 years ago
by user3262
Not Answered

nRF24LU1 programs a byte through spi command,a strange problem occured... 0

before i write the flash, it has been erased.so ,its value is all 0xff. when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...

421 views

0 replies

Started over 12 years ago
by user3353

Recent in Nordic blog

Introduction of SDH and SDK v15.0 software architecture

user63771

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

user46557

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

user4528

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018

Latest guides

Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

user72692

Check out older versions of this tutorial: nRF Connect SDK Tutorial series - Part 0 | NCS v1.2.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.3.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1…
- 24 May 2019
Hardware design, RF test and coverage: External GPS antenna on nRF9160 DK

user17630

The nRF9160 DK comes with an on-board antenna for GPS, but on some boards this antenna is not functional on board versions up to and including v0.8.2 due to this errata. It can also be very practical to…
- 24 May 2019
Getting started: How to get modem trace using “Trace Collector” in nRF Connect

user2124

UPDATE MAY 2021:Please follow the official documentation in infocenter. The following information is deprecated, please follow the documentation link at the top. Trace Collector app collects UART traces…
- 30 Apr 2019
Getting started: Store dust sensor data on nRF Connect for Cloud

user24652

In this example we are using the nRF Connect for Cloud Device API, which is a free service for protyping IoT products and is built on top of AWS IoT, to store dust sensor readings. The API is device-agnostic…
- 12 Mar 2019
Mesh Networks: Provisioning and running Nordic's BLE Mesh with Python Application Controller Interface (PyACI)

user17370

Purpose This document will explain the Mesh Demo and the motivations behind the design decisions. Please find attached PDF file at the bottom of this tutorial for high-resolution version of this tutorial…
- 3 Feb 2019
Getting Started : Using GDB with Nordic devices

user4528

The GNU Debugger (GDB) is a popular tool that provides familiar features like breakpoints along with a command syntax that allows creativity in the debugging process. Although its command line interface…
- 31 Jan 2019