Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Control GPIO by PPI and timer1 +1

I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000. I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...

1388 views

0 replies

Started over 12 years ago
by user2697
Not Answered

One command execution time on serialization 0

Hi, I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...

481 views

0 replies

Started over 12 years ago
by user2920
Not Answered

get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE 0

I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...

2118 views

0 replies

Started over 12 years ago
by user3506
Not Answered

HOW do I erase SDK5.2 version of flash and read not, in SDK4.2 can. 0

Hello: Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...

1007 views

0 replies

Started over 12 years ago
by user3262
Not Answered

nRF24LU1 programs a byte through spi command,a strange problem occured... 0

before i write the flash, it has been erased.so ,its value is all 0xff. when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...

421 views

0 replies

Started over 12 years ago
by user3353

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

user7328

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

user25682

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

user6207

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

user72692

Check out older versions of this tutorial: nRF Connect SDK Tutorial series - Part 0 | NCS v1.2.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1.3.0 nRF Connect SDK Tutorial series - Part 0 | NCS v1…
- 24 May 2019
Hardware design, RF test and coverage: External GPS antenna on nRF9160 DK

user17630

The nRF9160 DK comes with an on-board antenna for GPS, but on some boards this antenna is not functional on board versions up to and including v0.8.2 due to this errata. It can also be very practical to…
- 24 May 2019
Getting started: How to get modem trace using “Trace Collector” in nRF Connect

user2124

UPDATE MAY 2021:Please follow the official documentation in infocenter. The following information is deprecated, please follow the documentation link at the top. Trace Collector app collects UART traces…
- 30 Apr 2019
Getting started: Store dust sensor data on nRF Connect for Cloud

user24652

In this example we are using the nRF Connect for Cloud Device API, which is a free service for protyping IoT products and is built on top of AWS IoT, to store dust sensor readings. The API is device-agnostic…
- 12 Mar 2019
Mesh Networks: Provisioning and running Nordic's BLE Mesh with Python Application Controller Interface (PyACI)

user17370

Purpose This document will explain the Mesh Demo and the motivations behind the design decisions. Please find attached PDF file at the bottom of this tutorial for high-resolution version of this tutorial…
- 3 Feb 2019
Getting Started : Using GDB with Nordic devices

user4528

The GNU Debugger (GDB) is a popular tool that provides familiar features like breakpoints along with a command syntax that allows creativity in the debugging process. Although its command line interface…
- 31 Jan 2019