Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24LU1 programs a byte through spi command,a strange problem occured... 0

before i write the flash, it has been erased.so ,its value is all 0xff. when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...

421 views

0 replies

Started over 12 years ago
by user3353
Not Answered
Use nordic uart service with native Linux stack from Java 0

I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
- bluez
- nus
- linux
1392 views

0 replies

Started over 12 years ago
by user3220
Not Answered
ANCS Hard Fault 0

Hi, I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
- ancs
821 views

0 replies

Started over 12 years ago
by user3381
Not Answered
RTC clear event synchronised? 0

I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
- rtc
973 views

0 replies

Started over 12 years ago
by user3220
Not Answered

Wake-up Times ? 0

Hi, how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ? And how long does it tai if after wakeup it had to communicate...

838 views

0 replies

Started over 12 years ago
by user2150

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015