Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Convert AN34 DTM Python script to C# 0

Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ? The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...

1126 views

0 replies

Started over 12 years ago
by user3211
Not Answered
nrf51822 UART Lost bit 0

Hi, I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
- uart
- nrf51822
1031 views

0 replies

Started over 12 years ago
by user2619
Not Answered

Interfacing LCD display with nrf51822 evaluation board 0

Hi, I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...

2338 views

0 replies

Started over 12 years ago
by user2463
Not Answered

nRF905 timing requirements when auto-retransmitting. 0

Hi, We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...

480 views

0 replies

Started over 12 years ago
by user3024
Not Answered

Running Nordic BLE code in Visual Studio Project 0

This is not a real question for support. It's more a success story i'd like to share with you! Our company develops firmware for various customers on a lot of different...

3306 views

0 replies

Started over 12 years ago
by user2740

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

user7627

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

user6697

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

user7491

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015