Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Bluetooth mesh gateway architectures and implementations 0

Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
- development
- software
- Protocol
- mesh
- Other
- linux
70 views

0 replies

Started over 4 years ago
by user91631
Not Answered
nRF Connect for Mobile nrfnndisconnects, when sending 0x01 as first byte 0

Hello Nordic Team, I have a nRF52833 DK with me. I am using nRF Connect SDK v1.8.0 and through that using Segger Embedded studio loaded the Light switch example to nRF52833...
43 views

0 replies

Started over 4 years ago
by user110654
Not Answered
What does it mean to be "connected"? 0

Hello, What is the difference between 2 devices which are constantly scanning and 2 devices which are connected? Also, how do I code 2 devices to connect to each other?...
60 views

0 replies

Started over 4 years ago
by user99041
Not Answered
nRF52840 DK stops to scan after 3 hours working 0

Help me please!!! nRF52840 DK stops to scan after 3 hours working. Project is based on central_nordic_uart_service. Scan params it works fine 3 hours and then BLE...
64 views

0 replies

Started over 4 years ago
by user103465
Not Answered
Can't implement AES 128 CTR algorithm 0

Hi. I'm working with an NRF5340DK using NRF Connect SDK in a project where I need to decrypt an input text with a previously adquired key usign AES128 CTR, but I've been...
57 views

0 replies

Started over 4 years ago
by user106538

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

user2117

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

user9822

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

user4922

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015