Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
how to deal with NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE 0

I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
406 views

0 replies

Started over 9 years ago
by user14143
Not Answered
Internal flash as a Non volatile storage for user data 0

Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash. External Flash memory has a lot of drawback in comparsion with internal...
- flash pstorage
908 views

0 replies

Started over 9 years ago
by user15120
Not Answered
List of available peripherals 0

Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]? I am using NRF5182...
- list
- peripheral
- nrf51822
- scan
639 views

0 replies

Started over 9 years ago
by user12552
Not Answered
How to get APP_ERROR_CHECK(err_code) to print out error msg instead of reset? 0

I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
- 130 sdk11 ble
- bluetooth low energy
1110 views

0 replies

Started over 9 years ago
by user6674
Not Answered
ble_app_uart does not support DFU(Device Firmware Update) 0

Hello All, I have problem with ble_app_uart which are not support DFU services. When I am implement both services device will not advertise. and when ble_nus uninitialized...
- nrf52
- ble_uart
- ble
- nrf51
- dfu
- ble_nus
767 views

0 replies

Started over 9 years ago
by user12833

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

user7328

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

user25682

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

user6207

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Hardware design, test and measurement: nRF52832 Specific PCB Guidelines

user9102

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

user2124

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

user89293

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Hardware design, RF test and coverage: Using nRF9160 against R&S CMW500 (or CMW290) in signalling callbox mode

user89029

This blog clarifies what are the basic requirements when nRF9160 is used in signalling/RF testing against R&S CMW290/500 test setups. Setting up: The RF attenuations can be modified from RF settings->RF…
- 31 Mar 2020
Bluetooth low energy: Mocking CoreBluetooth

user3284

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

user24652

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020