Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

I am trying to write the bsp for nordic nRF51. I added the device information service and i want to change the system id of the DIS (dis_init.p_sys_id) without success . Can you please tell me how can i do it. Thank you. 0

dis_init.p_sys_id->manufacturer_id = 0x5555; dis_init.p_sys_id->organizationally_unique_id = 0x5555; This is not change anything.

384 views

0 replies

Started over 9 years ago
by user14642
Not Answered

Looking for developer in Minnesota, N. Dakota, S.Dakota 0

Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...

386 views

0 replies

Started over 9 years ago
by user14639
Not Answered

nRF52 EasyDMA must be on all the time? +1

I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...

1080 views

0 replies

Started over 9 years ago
by user4482
Not Answered
Multiple nrf51288 uart connection 0

Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 . idea similar to this: ...
- nrf51822 mbed
1138 views

0 replies

Started over 9 years ago
by user14563
Not Answered
SPI: Cannot write to full LCD screen 0

Hi, I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI. Currently the code writes two numbers and a...
- nrf51422
- nrf51
508 views

0 replies

Started over 9 years ago
by user14414

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

user82532

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

user27011

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

user7571

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015