Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

I am trying to write the bsp for nordic nRF51. I added the device information service and i want to change the system id of the DIS (dis_init.p_sys_id) without success . Can you please tell me how can i do it. Thank you. 0

dis_init.p_sys_id->manufacturer_id = 0x5555; dis_init.p_sys_id->organizationally_unique_id = 0x5555; This is not change anything.

384 views

0 replies

Started over 9 years ago
by user14642
Not Answered

Looking for developer in Minnesota, N. Dakota, S.Dakota 0

Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...

386 views

0 replies

Started over 9 years ago
by user14639
Not Answered

nRF52 EasyDMA must be on all the time? +1

I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...

1080 views

0 replies

Started over 9 years ago
by user4482
Not Answered
Multiple nrf51288 uart connection 0

Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 . idea similar to this: ...
- nrf51822 mbed
1138 views

0 replies

Started over 9 years ago
by user14563
Not Answered
SPI: Cannot write to full LCD screen 0

Hi, I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI. Currently the code writes two numbers and a...
- nrf51422
- nrf51
508 views

0 replies

Started over 9 years ago
by user14414

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

user82532

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

user27011

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

user7571

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Hardware design, test and measurement: nRF52832 Specific PCB Guidelines

user9102

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

user2124

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

user89293

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Hardware design, RF test and coverage: Using nRF9160 against R&S CMW500 (or CMW290) in signalling callbox mode

user89029

This blog clarifies what are the basic requirements when nRF9160 is used in signalling/RF testing against R&S CMW290/500 test setups. Setting up: The RF attenuations can be modified from RF settings->RF…
- 31 Mar 2020
Bluetooth low energy: Mocking CoreBluetooth

user3284

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

user24652

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020