Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

low power uart mode leaves TX asserted while CTS is disabled 0

I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...

399 views

0 replies

Started over 10 years ago
by user5346
Not Answered
BLE nRF OpenMesh - data rates in typical configurations 0

Hello, I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture. I'm considering using it in a network consisting...
1141 views

0 replies

Started over 10 years ago
by user13499
Not Answered
Is it useful to simulate my PCB design using CST Studio?and How? 0

Hello Nordic Community, I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
1465 views

0 replies

Started over 10 years ago
by user13147
Not Answered
registering to listen ble_ancs_c events 0

Hi. I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
- nrf52 s132 ble ancs sdk v11
613 views

0 replies

Started over 10 years ago
by user12617
Not Answered
PCB antenna used in the nRF51 DK 0

I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
- antenna nrf51dk
579 views

0 replies

Started over 10 years ago
by user13357

Recent in Nordic blog

I tried 5 different debugger IDEs for nRF52 and STM32. Here are my results.

user25488

At Jumper we’re developing tools that increase the happiness levels of embedded software developers. Our main tool to date is the Jumper Emulator. As a part of the development process we’re required to…
- 9 Aug 2017
Things you should know about Bluetooth mesh

user3110

Bluetooth SIG has recently published a new standard, the Bluetooth mesh. The mesh capability is a significant update and enables radical new applications. This in turn means that there are significant…
- 7 Aug 2017
New Command Line Interface - part 1.

user18697

Introduction With nRF5 SDK v14.0.0, we have significantly refactored the Command Line Interface (CLI) module to make it more useful and user friendly. The new CLI has the following features: Support…
- 3 Aug 2017

Latest guides

Software Development Kit: Radio Notification

user6606

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

user6606

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
Hardware design, test and measurement: nRF51 series current consumption guide

user2110

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

user3500

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015