ZIGBEE

RE: ZIGBEE

user92402 — Fri, 10 Jun 2022 11:30:11 GMT

Hi,

This issue is not related to the original problem in this ticket, so please create a new ticket for this issue.

Best regards,

Marte

RE: ZIGBEE

user116503 — Fri, 10 Jun 2022 02:18:23 GMT

I have installed NCS and tried to use debug mode it works well .but when i leave debug mode he doesn't work.do you have any ideas?

RE: ZIGBEE

user116503 — Thu, 09 Jun 2022 07:41:13 GMT

Attached my sch for your reference

RE: ZIGBEE

user116503 — Thu, 09 Jun 2022 07:23:45 GMT

I can't see any uart data (no--booting zephyr....), until when I execute erase all, the uart data is out

RE: ZIGBEE

user92402 — Thu, 09 Jun 2022 07:03:13 GMT

Hi,

From your picture it looks like it works, as that is how it should look when using the shell. Are you able to write any of the commands from the documentation I linked to, Radio test?

Best regards,

Marte

RE: ZIGBEE

user116503 — Thu, 09 Jun 2022 03:24:33 GMT

It works very well on 52840dk, but it doesn't work on my own board. But I found that when I erase all, there will be uart data as shown in the picture below, do you have any ideas?

RE: ZIGBEE

user92402 — Tue, 07 Jun 2022 12:50:05 GMT

Hi,

I have modified and built it for nRF52840 now, so please check if these hex file works.

test-devzone.nordicsemi.com/.../radio_5F00_test_5F00_nrf52840.hex

Best regards,

Marte

RE: ZIGBEE

user116503 — Mon, 06 Jun 2022 04:12:41 GMT

I tried the way you provided and it didn't help. Can you help use nRF Connect SDK Build an HEX FILE for test , use NRF52840 and modify the UART PIN definition as follows
RX_PIN->P0.14
TX_PIN ->P0.13
HW FLOW CONTROL->Disable

thanks

RE: ZIGBEE

user92402 — Fri, 03 Jun 2022 09:15:27 GMT

Hi,

Can you try using using start_duty_cycle_modulated_tx instead of start_tx_carrier and see if it works?

If this does not help, can you try with the Radio test sample from nRF Connect SDK? I have built the sample for you in case you do not have this SDK and its toolchain installed. Since you did not specify what board you were using I built it for nRF52 DK based on your mention of nRF52832 in another ticket. If this is not the board you are using, let me know and I will build it for another board. For testing see the sample's documentation here: Radio test

test-devzone.nordicsemi.com/.../radio_5F00_test_5F00_nrf52832.hex

Best regards,

Marte

RE: ZIGBEE

user116503 — Thu, 02 Jun 2022 01:20:45 GMT

data_rate ieee802154_250Kbit

output_power pos8dBm

start_channel 11

end_channel 11

start_tx_carrier

RE: ZIGBEE

user92402 — Wed, 01 Jun 2022 10:13:32 GMT

Hi,

What commands are you using in the radio test example to perform the test?

Best regards,

Marte

RE: ZIGBEE

user116503 — Tue, 31 May 2022 11:10:14 GMT

thanks for your reply*.

I use the \examples\peripheral\radio_test to test tx power.Then we found psdu crc fail on our test equipment. I want to know how to fix PSDU crc fail

RE: ZIGBEE

user92402 — Tue, 31 May 2022 09:52:37 GMT

Hi,

In your other ticket (289849) you mention using Zigbee CLI Agent, as well as something called audio_test example code, but here you say that you are using radio_test. Can you clarify what example you are using, and explain what you are testing and how you are testing it? Also, if you want to test the 802.15.4 radio I would recommend using IEEE 802.15.4 PHY test tool from nRF Connect SDK, as nRF5 SDK is in maintenance mode.

Best regards,

Marte