Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
I have a Thread bench-top environment set up that includes
One nrf5340dk flashed with the openthread coap_server firmware build and flashed on 1.8 via Visual Code
Two...
Hi
If a bug stop the application to feed the wdt,Is there any way to store 8bytes application data to flash before reset which occurred by wdt?
I find that there is only...
Hi,
I'm having some difficulties understanding how to manage commands in endpoint-specific callbacks. For example, when receiving a "ZB_ZCL_CMD_CONFIG_REPORT" I'm able to...
Hello,
I have a peripheral (nRF51822, S130, using the peer manager) that should be paired/bonded with one or many centrals. I have followed the example ble_app_bms from...
Hi everyone,
I implement nrf5_SDK_17.0.2 ble_app_uart example and I use an android app like nRF_Connect to receive the uart data on my cell phone.
The problem is that...
Hello,
I am having an issue with the nrf_libuarte_async librairie.
I am sending data via nrf_libuarte_async_tx and receiving the data properly via the IRQ handler...
Hello all, I am currently trying to get the nrf sniffer into the hardware of my nRF52840 DK board. Unfortunately when I call the programmer via the nRF Connect Desktop APP...
Hi, I am working on ble_app_uart_pca10056_s140 and after 3 minutes and I am getting the following error.
When I change APP_ADV_DURATION to 0 also get the following error...
Hi,
We have a product based on nrf52840 which is already in production for several years. It was built over SoftDevice132 and SDK 12.3.
The project has 2 components: ...
SD140
nrf52833, custom application based BLE Central Uart Project.
We would like to try the UART DMA functions available in Soft DEvice, s140_nrf52_7.2.0.
I have not...
I am trying to get I2S communication up and running but am unable to produce a signal on my SDOUT pin. MCLK, LRCLK and SCLK work as intended but trying to send any data does...
Hi! I've recently received my Thingy:91 and wanted to get it up and running. I followed your video ( https://www.youtube.com/watch?v=xQ7hDzRULJQ ), although did not see the...
Hi,
I am testing direct advertising with two nRF52-DK. One performs a direct advertising and the other scans for the directed adverts. Unfortunately, the scanning device...
The NRF52840 specifies a 20%, 10uH inductor for the integrated DCDC convertor. Why is the inductor value so large? This switcher runs at 8MHz, which usually means something...
I have been tasked to use out-of-band authentication for the nRF5340 using the NRF Connect SDK (Zephyr based). Is this feature supported within the SDK. Is there an example...
