Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Devzone,
I've been trying to verify and validate the performance of Instaburst mesh packets against regular ones. I modified a build of the mesh light switch example...
Hello,
I have been trying to get the thingy:91 up for 3 weeks or more now from Sri Lanka. I have made a lot of progress in getting data connectivity via MQTT to thethings...
`Hi There,
For nRF52840 board, If I want to fully disable JTAG or SWD lines after flashing, then what are the options to achieve it.
Questions:
1) If I want to disable...
My use case: There are different but similar peripherals advertising with 1M uncoded or coded PHY. Some of them are even advertising in mixed mode.
Question: How to connect...
Hello all,
I hope you are well. I am currently developing a product on the nrf52810 platform. I have a custom board and now have the BLE functional on the board. The next...
Good Day.
I want to measure the approximate voltage level on the battery in the nrf52820 microcontroller using a comparator (COMP) operating in Single-ended mode. I use...
am following the introductory videos and have done a fresh install of the Toolchain, Segger, VS Connect 3.7.2, nRF Connect SDK v1.8.0 and VS code on macOS
1. Installation...
Hi team,
I'm currently playing around with the sensor server example where I wanted to include the generic_onoff model in a separate element. I wanted to learn how to add...
Sure, my question is very stupid, but after one day I found nothing to explain the principle of the situation, I decided to ask.
I have a laptop with built-in Bluetooth...
Hi all,
I am trying to interface IS25LQ040B serial flash(512KB) IC with nrf52833 (bl653_dvk).
programmed sample code from "zephyr\samples\drivers\spi_flash"
I am getting...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
Hi,
I want to use the 64MHz crystal oscillator (HFXO) as the source for HFCLK clock controller. How can I need to enable or disable the item in KConfig on nRF Connect SDK...
Hi,
My project has a requirement to toggle the GPIO output in 400 to 500 microseconds cycle, I've tried to use the Timer on Zephyr but it can't supply a stable cycle in...
Is there a current example for nRF52840 power management under Zephyr / nRF Connect SDK?
Searches for this turn up old examples, such as this one , that are no longer in...
