Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I just install the NCS in toolchain manager, but after installation, only one toolchain folder is there,no zephry,no examples,
I'm going to play in VSCode.
what should...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough "RSSI > -45" and initialize...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement my firmware which will consume less current. I have implemented...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. Our custom board has a connection to nRF GPIO...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We need to publish the JSON messages larger than...
Hi, I am developing my own application using the SDK v1.8.0 with Demo direction_finding_connectionless_rx. I notice that in the
cte_recv_cb callback function, the rssi...
Hello,
I am using nRF 52840 DK board and using nRF52SDK17.0.2. I am trying to advertise data in GAP with the name " IG_Last4CharMAC_RFL " for example " IG_4DA8_RFL " but...
hello,
NCS1.9.1, Windows10 X64,nRF5340-DK, nrfx_i2s
in file boards\nrf5340dk_nrf5340_cpuapp.overlay
i've i2s DAC model ,it must use 4 line(MCLK,SCLK,SDIN,LRCK)
but...
I am trying to get this example program https://github.com/ARMmbed/mbedtls/blob/mbedtls-2.11.0/programs/x509/cert_req.c (stripped out all the file handling stuff) to run on...
Hello,
I crated a custom peripheral for my application, I took the code from the Blinky example and i changed the service.
I set the FIRST_CONN_PARAMS_UPDATE_DELAY parameter...
I would like to be able to use 3 different USB descriptors.
1. CDC ACM
2. Mass Storage
3. Composite device with CDC ACM and Mass Storage
These should be selectable...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK. I am using openthread protocol...
