Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear nRF,
I have couple of nRF21540-dk boards (PCA10112) in my hand. I would like to use nRF Connect Direct Test Mode to activate TX and RX.
I found that the tool lacks...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
I am taking over a firmware Bluetooth project and am reading the code that is having some issues. Below is a snippet from a BLE characteristic read callback. Here a double...
I set a timer on the net core of nrf5340. The timer sets an interrupt of 10s. After the chip is reset and runs for 10s, the while (1) of the main function is interrupted,...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
If I add CONFIG_LOG=y to "prj.conf" in the zephyr sample peripheral_dis, when...
Hello,
I'm working with a NRF52840 DK and a module BLE nrf805.
I'm programming thanks to the software SEGGER.
I have sent the blinky simple in my dev kit to test a...
Hello,
I am using the Segger Embeddd Studio from the nRF Connect Desktop and the nRF52840-DK board.
I am working over the project into the "ses" directory for SoftDevice...
Hi,
Do you have an example of the \ble_peripheral\ble_app_hrs with Coded PHY for the nRF5_SDK_17.1.0? I have tried to use the BLE_GAP_PHY_CODED definition in different places...
Hi,
Is it any possible setup to connect a NRF52840-DK to the nRF Connect app in a smartphone without pairing or bonding? That would help me for testing and in this stage...
Hello
I am launching a project and I intend to:
Want to use multiple mobile phones and nrf-mesh software, Connect to a mesh server and turn on or off a led
So I connect...
This commit to the sdk-nrf repo: https://github.com/nrfconnect/sdk-nrf/commit/fdd7a24857a6e762055a0192293fc85165246e7f appears to me to indicate that hardware crypto support...
Hi, There：
Can the mesh device be modified the APPKEY,NETKEY,DEVKEY and the unicast address after be provisioned? And How?
I had tried to modify these parameter provide...
Hi team,
Currently we are using nRF52840 in our project.
we have plans to redesign the hw
does nRF52833 have any advantages over the nRF52840?
if so, Could you please...
