My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
hi
i'm new to the nRF platform and realised it uses zephyr. i come from a pic & stm32 background with little rtos knowledge and find the official zephyr cryptic. especially...
Hello,
according my Observation Zephyr, more precisely the rpmsg stuff for BLE between both nRF5340 cores, doesn't work when optimization is switched off. But stepping through...
hello Nordic
i am working with nrf52840 with ncs (on the process of moving to 1.8 currently 'v2.6.99-ncs1-1' )
i have several sensor drivers on my board and flash driver...
hello,
i am using nrf52832 with lis3dh accelarometer and max30205 temperature sensor in our customised board with sdk 15.2 i have included the dfu ota in my firmware my...
hello nordic team I ran the ble_app_uart example in sdk 15.3.0 on nrf52832. When i add printf("\r\n%d\r\n",15); to the code as follows, the program prints 15 to the serial...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a process to set the characteristic and send an indication using sd_ble_gatts_hvx...
Thank you very much for your help. I am currently working on implementing a PWM control function using the nrf52840. I would like to ask you about a build error that occurred...
Hello All, I am trying to figure out how to use the PWM.h driver for the nRF9160 to read an input pwm signals pulse width and period (im currently working with the nRF9160...
I need to know in which case the SIW_DET pin is used. Does it depend on the version of the nRF9160 ? Then which versions ?
And is this detection function better in software...
Hello, guys!
I am using nRF51822 SoC with Zephyr. There is a need to configure multiple GPIOs as inputs, with the possibility to fire an interrupt on rising/falling/both...
Hi There,
I am working on a project based on nrf51822. I need to establish pairing the device with smart phone by clicking a button as confirmation on the nrf51822.
...
Hello,
I already fully understand how nRF5340: Network core bootloader working.
As I wondered in the title, I want to move the application firmware data of network core...
The project uses nRF5340. A signal is connected to P0.27/AIN6, and during "normal" mode the pin is used as an ADC.
Before going into sleep mode we would need this pin to...
Hello,
I am working on a project which is based on nrf52840 and Zephyr.
Current prototype uses Adafruit nrf52840 sense board with spi based display attached.
I am new...
Hi,
I experience a very strange issue with UART.
When I try to send data via /dev/ttyACM0 device it looks like the characters sent are buffered and sent only upon the...
