Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I am working on nRF52840 DK and dongle. I am trying to implement a firmware that can scan device and send command through NUS. So I use ble_app_interactive example...
So, this could just be an odd coincidence, but I'm stuck.
I had a project working using standard advertising. You connect, pair, and then the client (nRF Connect on Android...
Hi! I'm trying to encrypt some data using ECC 256 but I have some issues:
-I found a code ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/crypto...
Hello! I'm trying to use a custom SPM using this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
I closed the previous discussion by mistake: https://devzone.nordicsemi.com/f/nordic-q-a/83067/nrf9160-board-for-qr-code-project?ReplySortBy=CreatedDate&ReplySortOrder=Ascending...
Hi there
The project that I am focusing on was really time-critical, so I'm wondering whether we could disable Link Layer ACKs in nRF Connect SDK (i.e. Zephyr) ? If not...
We have been looking at InsightSIPs AoA Demo kit ( https://www.insightsip.com/products/bluetooth-smart-modules/isp1907 ) and are trying to understand the communication protocol...
Hi,
I would like to secure my application using security mode 1 level 3. LE Legacy pairing with OOB key sharing. (both master and slave device does not have I/O Capabilities...
Is there a way to access the data that comes into a provisioned node and is relayed on the mesh network, from the application layer in Zephyr?
I have a battery models erver...
Our product under development has tight flash requirements. As such, any optimisation to the build size of the product has a great affect on further development, therefore...
Hi Everyone,
I have seen some posts regarding this topic on the forum but would just like to clarify a few things.
I am currently using an application timer to sample...
Hi,
The nRF Connect Extension on my Windows VS code doesn't load altogether:
I uninstalled VS code - including all it's settings/extensions etc using this post's suggestion...
This issue exists in SDK 15.2 and earlier.
In nrf_log_frontend_dequeue() when memobj cannot be allocated, the backend flush api is used to free memory. However this memory...
Hi.
The VS code extension Cortex-Debug reports:
' WARNING: Cortex-Debug will deprecate use of GDB version 8. Please upgrade to version 9+ '
The manual installation...
