Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
We have a mature product based on the STM32 ARM processor family running the uCOS OS and our development toolchain is IAR. The workflow has worked well in the past when...
Dear all,
I ran LPCOMP example from SDK16 on nRF52 DK and it works just fine.
But I've occurred some problem modifying reference voltage. I init the lpcomp the same...
Hi ,
I have my own custom nrf52832 pcb. I have 2 chips on my pcb.
I program my device with Nrf52 Dk.
When I program MCU 1. The program is uploaded successfully and i...
Hai
I'm using nrf52811 and sdk17.1.
I tried all peripheral examples But I can't set advertising data to more than 31 bytes.
If I increase the data size some parameters...
Hi , I am using ZEPHYR rtos , and using the internal bootloader and its working fine and there are two images but now my code size has increased and i can not store 2 images...
Hi
I want to use app_uart_put() to send an array which is over 4096 bytes.I try to change the value of UART_TX_BUF_SIZE to 10K bytes，then call the app_uart_put() to send...
Hey
what are the downsides of using the already burned-in Random Static Device Address compared to a Public Address?
My assumptions are as follows:
Pro
Con...
Hi,
I have been working on Zephyr for the past weeks and have been able to set multiple GPIOs, interrupts and RF functionnalities. But so far, I thought I could handle...
We'd like to use Thingy91 to measure temperature, but it looks like the thermometer (BME680 onboard) gets heat up, when Thingy91 is running for some time.
I placed the device...
Hi,
I'm supporting a customer who is planning to use T-Mobile as their carrier. One of T-Mobile's questions is:
APN requirements: Private APN requires an IPSec VPN or...
Hi,
The spi_config structure zephyr provides is as below: Wherein cs is initialized to the chip select pin. In my project I have a requirement to handle 2 slaves which...
There is a bug in the sample/nrf9160/at_monitor, namely to do with +CEREG unsolicited notification handler called "cereg_mon". "cereg_mon" expects 0-2 +CEREG status code,...
I'm trying to replace a RS232 cable with a BLE bridge with the Nordic Uart Service.
One nRF52832 configured as central (app_uart_example_central) and an other one as peripheral...
Hello,
We are working on a product that contains nRF51822. The product sends continuous data (2 bytes) via NUS service to the mobile app at a frequency of 200ms.
When...
