In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Dear All.
I tried to test and evaluate LoRaWAN stack on Zephyr, without success. I will need more time to debug what is happening by the logic analyzer. Meantime I attached...
Hi,
I have enabled SPIM on nRF52810 and worked normally.But when I enabled on nRF52832, it worked unusual.
I had defined CONFIG_NFCT_PINS_AS_GPIOS because used P0.9 and...
Hello,
We are using lwm2m client project SDK version v1.9.0. We need to enable #define CONNMON_LAC 12 to get LAC value but i am facing problem to enable #if defined(CONFIG_LWM2M_CONNMON_OBJECT_VERSION_1_2...
Hi,
When I download the example of "ble_app_uart"(SDK17.0.2 S132) in nRF52832,mty board is working as normal. But when I add RNG in main, the RTT Viewer just logging SOFTDEVICE...
I have some odd cases where an nrf53 based device just disappears from BLE. It's no longer connected, and not advertising.
I'm looking for a method for the application processor...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. A port is connected to the board to communicate...
Included "bsp.h" and "nrf_fstorage.h" still getting these below errors:
undefined refence to `bsp_indication_set'
undefined reference to `nrf_fstorage_init'
undefined...
Hi,
I use the nrf mesh sdk for long time and I just see that its migrate to zephyr rtos.
After reading the nrf mesh sdk doc and the zephyr project doc, I have some questions...
Good afternoon.
We're using nrf Connect for mobile to perform DFU over BLE to an nrf5340-based module with firmware built using the nrf connect 1.6.1 SDK and its associated...
0 dBm TX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 7.1 mA
Radio RX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 6.5 mA
I want to know which example is tested...
The CAN controller MCP2515 should be connected to the Nordic DK NRF5340 by the SPI interface.
Communicate to Arduino uno
We were trying with CAN sample given
But this...
Hello,
I've tried to request the location via AGPS/PGPS via Location sample in SDK 1.8 but it seems that location is only working with the Cellular method.
I've tried...
Hello there, I am new to your product, and I am trying to understand your library logic and hierarchy. Right now I am trying to figure out what all of these prefix (such as...
Hi, I want to use an NRF52805 with a voltage to frequency detector. If I understand the datasheet, there is one timer/counter and RTC on that chip. Is it possible to set the...
Hello,
How do I deactivate/activate a SDA/SCL line?
I perform a test on an Icarus board with a VL53L1X sensor, everything works fine.
However, in idle/sleep mode, whether...
