I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Setup: Windows 10, nrfutil verison 6.1.3, python 3.10.2, nRF 5 SDK 17.0.2
I have a custom board running the stock DFU firmware from the nRF5 SDK. The only changes we made...
There are many questions on DevZone on modifications to NCS peripheral_uart/central_uart NUS example applications to support higher throughput.
We have been mostly successful...
I would like to use the nrf connect sdk to connect to a device and 'discover' the GATT services it supports, the characteristics in each service, and then read the descriptions...
Hi everyone!
I ported some project from NRFsdk 17.0.2 (all works fine) to Zephyr rtos and faced with issue - when set high speed uart (460800 - 921600) then some bytes ...
Hi All
A few times ago, I installed the nRF Connect for Desktop v.3.8.0 on my PC.
Getting started assistant, Programmer, Toolchain manager apps were installed and everything...
I want to know about following things:
1). NRF_SDH_BLE_GATT_MAX_MTU_SIZE
2). NRF_SDH_BLE_GAP_DATA_LENGTH
3). NRF_SDH_BLE_GAP_EVENT_LENGTH
4). Connection event length...
Hi There,
I facing one critical issue with softdevice, I cannot get it work in freertos environment.
Hardware: customized board based on PCA10056
SW: nRF5_SDK_15.2.0_9412b96...
HI
I am using the I2S on the nRF52840DK I have constructed an array and all works well except once I start it , it continues to run, I cant get it to play the sample just...
Hi,
In the product I developed, there is a UI flow about the mode of pairing and binding, which has a limitation that it can only be paired and bound when entering this...
My nRF52 only advertises NUS.
When a phone connects (Android or iPhone), I want to force bonding.
It seems to be related to security. I have tried a couple things, but...
Hello ,
I am using nrf52810 and i have my own code and once its compiled hex file is created so if in case if i missed my source code and i had only my hex file is it possible...
HI I am using nRF52DK as central and peripheral. UART example was used in nRF52DK as central, and blinky examples were put in the rest of nRF52DKs to test the connection....
Hi,
Disconnecting connection during DFU, then DFU never works again.
I reboot device many times.
Application works fine and soft device works fine, buf DFU still fails...
Dear Dev-Zone Team,
I just got my PPK2 and wanted to test it on the nrf52840
It seams to work fine, I can see the advertisement peaks, however the average power consumption...
I am using vscode with NCS 1.9. I am trying to add RTT logs to MCUBoot as the product I am developing won't have an exposed Serial port. I started with the hello_world example...
