An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
I'm using nrf52832 (S132 v7.0.1, SDK v17.0.0) to develop peripheral roles.
Setting UUIDs for advertisements, services, and characteristics. At that time, sd_ble_uuid_vs_add...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central and Android device (Bluetooth 4.2) as advertise. Android devices use nRF Connect.
I can set...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
Hello,
I am new to Nordic, Zephyr and Linux. I have been going through the "getting started guide" on the zephyr docs website and ran into this problem not being able to...
I heard that nrf52832 rev3 has been released. Our product is using nrf52832 rev2, nrf SDK 15.3. If we change the chip to rev3, can we use the firmware without modification...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
As we can see that there is...
Hi,
I am trying out the smp server example with mcuboot and encounter this error when building for the nrf52840 dongle.
I read that it has something to do with the usb...
1. Erratum #7 counsels to add a DSB if reading sequentially from UICR and program flash, as below. But what constitues sequential? If my program reads from UICR on a thread...
I have a BLE application I'm writing using SDK17.0.2, and want to use FDS for some persistent storage. The first thing I want to do is to allow the user to update the name...
Hi,
I am using nCS v1.8.0 for application development on nRF Connect extension of vscode.
But I am unable to configure any unit testing framework to test my applications...
Hi, I am developing a logger for which I am using a memory. I was doing all this using SPI in nRF52832 DK which works perfectly fine. But the problem arises when I am trying...
I have a module using a Nordic chip labelled "N51822QFAAH01621UT". I know it's the NRF51822-QFAA, but I am not sure which model exactly?
Looking on DigiKey these are the...
This is more of a question than a problem:
I have been studying the ble_app_uart_c code and noticed that although data is transmitted to the handler one byte at a time,...
Hello.
We are looking for a viable solution on how to transfer a firmware over the BLE OTA from Particle Tracker (Gateway), or any other mcu to nRF52840 devkit (Client)...
Dear, I am new to Nordic. I trying to understand the various Defines for nRF5340DK kit using Devicetree.dts file. In that, I had look on SW0 defines.
1. The gpio0 reg is...
