Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I use nRF52840 in aQFN73 package. Can I assign QSPI contacts to G1, J1, L1, N1, R1, U1 pins? Or should I strictly follow the recommendations from the datasheet? Thanks.
Hi All,
I have an application that wants to send 1 array every 2ms. There are 10Bytes of data in the array.
I will be based on 1Mbps, MTU size = 23byte, Payload = 27byte...
Today I opened VS Code to find all my Zephyr/NRF #includes have the red squiggly lines with an error such as "cannot open source file zephyr/types.h". Right click -> Go to...
Dear Sirs,
I use the standard printf() function to communicate via UART (with retargeting).
Unfortunately could not find a way to not overwrite a buffer.
The only workaround...
I have configured EasyDMA RX.MAXCNT=256 and set EVENTS_ENDRX. If >=256 bytes arrive, an interrupt occurs immediately. And if only 128 or 10 or 203 come.. byte, then I'll never...
Hi,
I'm using nRF Connect SDK 1.7.1.
Is it possible to mix polling & interrupt driven UART API?
I have a situation in which I want to receive input once in a while...
Hello,
I am using the Bluetooth Low Energy application to interact with my device under development. I notice that if I set the Write No Response property on an attribute...
Hello, I have recently started an evaluation on nRF9160 DK in the UK. I tried to run the Serial LTE or AT Client examples but I was not lucky to register to a network. Using...
Hi to everybody, i'd like to know if there is a way to enable/disable mesh message relying on a node locally by the firmware without using a configuration client or a provisioner...
Hi Nordic, Since the last update of the Programmer application of the NRF CONNECT for Desktop, I've been seeing this error: I've NRF52833DK // PCA10100, and up there it says...
Hi Sir/Miss,
I use programmer v2.3.1, J-link and nRF52810.
After I connect to J-Link which displays nRF52840 in UI. In log windows, it's normal.
Please check below...
I have been writing an app and now changing the bluetooth library to Nordic Android BLE Library. W hile connecting to the device I keep the autoConnect flag on, which lets...
Good morning/afternoon/evening to whoever is reading this.
I am fairly new to working with nRF tools, this is in fact my first time working with this. I have a linux virtual...
Hi,
Sdk-17.1.0
Soft device-s112
I have large amount of sensor data in my memory (eg:- 8MB of temperature sensor data, 100000 readings). I want to transfer this to the...
When the nRF52840 Dev Kit is sending data as a peripheral, connected to client running nRF Connect all works.
I am sending (streaming) a text file to iOS phone or Android...
