Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Is there any available binary firmware for nRF5340 Audio DK to evaluate and demo the LE audio case?
I tried to use the nRF5340 Audio DK for LE audio, but found the LC3 codec...
We’re using Nordic Semiconductor nRF52840 and we may have some problem with RTC when we simulate a brownout. In our application we have both coin cell battery and external...
when I am trying to setup linux with this link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/gs_installing.html#install-the-toolchain
On typing this command...
Hello!
I would like to know the gain of the integrated PCB antenna on the nRF52832 chip. Is there a documentation paper on the antenna itself? I couldnt find any info...
Hi!
I am evaluating DFU over Mesh by following the configuration guide here Configuring and performing DFU over Mesh . I am trying to prepare a package with the application...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I have a question about setting the UUID. My program has one advertised UUID...
I am using slightly modified master SPI example from here which is running on nRF5340 to communicate with slave device, which is RHD2216 . SPI frequency is NRF_SPIM_FREQ_4M...
Using a nRF52832, I would like to broadcast advertisement packets normally and in extended mode at the same time. Is this possible or do I have to ping-pong between, stop...
ok,i recenlty have gotten iq samples from Rx.but i think my received iq samples are from Tx .i use the NCS 1.9.1 with two boards nrf52833dk.
firstly,i connect antenna array...
Hi, I have already updated all certificates and firmware. But when I am trying to connect my device to the cloud it does not recognize my device. when I am trying to add my...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte in mode NB-IoT not in LTE-M?
Can we say that every time a data is sent, it takes 950...
Hello, All
I received following message when I test the code, it appears on both sides,
ASSERTION FAIL [chunk_used(h, c)] @ WEST_TOPDIR/zephyr/lib/os/heap.c :163
unexpected...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
I am after some assistance with creating a 6 layer stackup to use with the NRF52840_CIAA that is 1.6mm thick.
Can you provide recommend layer stack up that have been...
Hello.
Is there any difference between i2s hardware in nRF52840 and nRF52833? I made WS2812B i2s driver and working very good on nRF52840. The same code (project is adjusted...
