Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi! I am in the process of trying to install the Asset Tracker on my Thingy91. I have got it to work with nrfCloud and I am now trying to configure it to use the AWS backend...
I am using the nRF52 SDK : nRF5_SDK_17.0.2_d674dde
- When data are all ASCII-Hex (0x30) the code working fine
- Now I try to optimize code by changing to binary data....
I have been using the nRF52-DK for while and it been good.
But when I accidental hold the "BOOT/RESET" button, the board now stop working. only LEDs is blinking (per sec...
I would like to ask if someone from India ever used Thingy:91? Which SIM card is used or where to get the supported SIM card? How to get it working in India?
In VS Code, when pushing the " Connect To RTT In nRF Terminal " button, a message shows up:
J-Link V7.20 Device Selection The selected device "NRF52832_XXAA_REV2" is unknown...
Goodday all
Im trying to drive some Neopixel LEDs with 52840DK SDK_17.1.0. and have been following this example. https://devzone.nordicsemi.com/f/nordic-q-a/70560/nrfx_i2s...
I'm trying to install and run the nRF Command Line Tools, but am running into issues. I was able to successfully install the Linux32 version of the tools, but when I go to...
Hi
I am using nrf52840 and I want to use nrf_calendar example with app_ble_uart,
I am traying to send parameter from nrf toolbox uart app mobile
but I have no idea how...
Hi,
I am using nordic 52840 development kit along with sdk17.1
I am tried to use ble-uart example code to receive data from the app and based on the data i need to write...
I'm trying to follow the instructions to perform an OTA DFU for the Thingy 52.
https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/dfu_generating.html...
I'm using SDK 1.7.0. Here's how I have the modem code setup.
Init modem outside of thread loop
Set modem at+ comman CFUN=1 (start searching for a tower)
Once +CEREG...
hi,
when I call 'mesh_stack_device_reset()' function from the application, then the bootloader goes into infinite loop.
exactly at the point int the main() -> init_clock...
We are supplying the nRF52840 from 5 V into the VDDH pin. We are not using the USB interface, so I want to confirm what our options are for the VBUS pin. Can we leave it floating...
