hi, i am using a cutom board based on nrf5340 mcu , so, while setting it up i am facing the problem in checking logs and led status.
i am uisng the nrf5340dk board to build...
Hi Nordic technical expert，
Can random numbers in broadcast intervals be cancelled or fixed? How to modify the software? Could there be other problems if random number times...
I added ring buffer and UART ASYNCH interface to asset_tracke_v2. I added CONFIG_RING_BUFFER = y, CONFIG_SERIAL = y and CONFIG_UART_ASYC_API = y to prj.conf file. The build...
Hi,
I am looking at setting up some of our team with the ability to flash our custom devices that contain various chips (nrf52, nrf53, nrf91). Assuming the SEGGER software...
Hello,
I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below:
ATT MTU: 247
Data length: 27
Connection...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
Hello,
I have a BLE peripheral device that becomes the server once a connection is established. The BLE services and characteristics are all custom, I will include the defines...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central and Android device (Bluetooth 4.2) as advertise. Android devices use nRF Connect.
I can set...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
Hello,
I am new to Nordic, Zephyr and Linux. I have been going through the "getting started guide" on the zephyr docs website and ran into this problem not being able to...
I heard that nrf52832 rev3 has been released. Our product is using nrf52832 rev2, nrf SDK 15.3. If we change the chip to rev3, can we use the firmware without modification...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
As we can see that there is...
Hi,
I am trying out the smp server example with mcuboot and encounter this error when building for the nrf52840 dongle.
I read that it has something to do with the usb...
1. Erratum #7 counsels to add a DSB if reading sequentially from UICR and program flash, as below. But what constitues sequential? If my program reads from UICR on a thread...
I have a BLE application I'm writing using SDK17.0.2, and want to use FDS for some persistent storage. The first thing I want to do is to allow the user to update the name...
Hi,
I am using nCS v1.8.0 for application development on nRF Connect extension of vscode.
But I am unable to configure any unit testing framework to test my applications...
Hi, I am developing a logger for which I am using a memory. I was doing all this using SPI in nRF52832 DK which works perfectly fine. But the problem arises when I am trying...
I have a module using a Nordic chip labelled "N51822QFAAH01621UT". I know it's the NRF51822-QFAA, but I am not sure which model exactly?
Looking on DigiKey these are the...
This is more of a question than a problem:
I have been studying the ble_app_uart_c code and noticed that although data is transmitted to the handler one byte at a time,...
Hello.
We are looking for a viable solution on how to transfer a firmware over the BLE OTA from Particle Tracker (Gateway), or any other mcu to nRF52840 devkit (Client)...
Dear, I am new to Nordic. I trying to understand the various Defines for nRF5340DK kit using Devicetree.dts file. In that, I had look on SW0 defines.
1. The gpio0 reg is...
Hi, I'm using the nrf52840 BLE mesh (nrf5_SDK_for_Mesh_v5.0.0_src) and some other sensors which drivers are written by using nRF5_SDK_17.0.2. my device is battery operated...
