Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hello,
I am aware that this is not an Arduino support forum, but if I'm not violating any rules, I'd like to ask a question in hope that someone might have provide a helpful...
I'm developing on an iMac M1.
Over 2 month I tried to get the nRF Connect for desktop (V3.9.3) running on my M1-mac, without success.
Toolchain manager (v0.10.3) works...
Hi Nordic Team,
Currently we are exploring nRF52840 DK.
We have observed BLE Enable SOC usually have two cores, one as an application and one as BLE Soft Device core....
Hi - I am using the /nrf/samples/matter/lock sample as a reference template to develop my own app. Thank you for providing it!
I am able to build and flash the basic build...
After updating the firmware on NRF9160 Connect DK (using mfw_nrf9160_1.3.1.zip as well as the ltem asset tracker hex file) LED 3 does not turn on and AT commands in LTE Link...
I am using a mac M1, running macOS 12.0.1 Monterey.
J-Link Software and Documentation Pack v7.62 (latest)
NRF Connect for Desktop v3.10.0 (latest)
Programmer v2.3.1...
Hello,
i'm using a nrf52832 dk and i'm using the example ble app uart.
I saw the packets that are send for rx or tx but with packets of 20 bytes
I saw this post, https...
Hi,
I have some problem with NRF52840. When I use software example "ram_retention" in peripheral directory on 2 différents board I have 2 differents state of VBUS pin. ...
Hello,
I am relatively new to iOS development and have now made the iOS version of the nRF Toolbox from the Github. After some initial difficulties, I was able to get the...
Hi,
I have a peripheral device that running on nrf5340 and can be updated via MCUMGR SMP. i tested it via Device Manager application and it is working.
My question is...
I'm building a custom board based on nRF52840.
I'm providing 5V input via USB to VDDH & USB pins. The default output of the first internal regulator during high voltage...
Hi, before buying the PCA10056 kit, I have some questions about the USB CDC ACM example.
I'm new to the USB CDC ACM.
At the Infocenter , it says that
This example...
Hello everyone!
I have just got started working with Nordic devices, in particular the nRF9160. I have been doing tests using the provided UDP sample from nRF Connect SDK...
I tried building and running the buttonless DFU example project. However I get the following UART output:
It seems like it can download the softdevice by itself if the memory...
