SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Once connected to the peer, the app will begin with "sd_ble_gap_rssi_start()", and the peer will send RSSI sample to the softdevice, and the SD will back to APP with a "BLE_GAP_EVT_RSSI_CHANGED...
I use nrf connect sdk 1.9.0, to run periodic_adv and periodic_sync example.
The adv side sends this data: mfg_data[] = { 0xff, 0xff, 0x00 };
But in sync side in scan_recv...
Hi,
My mesh project is occasionally suffering some dropped messages and after probing around I found this on one of the nodes.
I have four nodes and one gateway running...
Hi,
In nrf52840 dongle, I use nrf_crypto_ecdsa_sign function to sign.
Everything is fine in when building, but when testing the real world data, it’ll will show error...
I use 52820 to do ble_usb+esb project, but I have encountered problems when adding USB. I have added USBD_HID_COMPOSIT in the project of \ examples \ peripheral \ usbd_ble_uart...
Dear community
I am developing an autarkic embedded system where I harvest energy from a thermoelectrical generator. It is a simple application, I need to acquire the open...
Hello,
NCS1.8.0 Windows10 X64;
i test v1.8.0\nrf\samples\bluetooth\direct_test_mode, and i want to use nrf21540 model.
i've set CONFIG_NRF21540_FEM=y and do Project...
nrfjprog restarts nrf5340DK debugger
We are running a container environment in Ubuntu 20.04 on WSL2 and the USB ports are frwarded using usbipd
When trying to flash (or...
Hi,
I have been playing around with the nRF9160 DK trying to get it reading a range of sensors, so far with success, however I have found an issue which has stumped me...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We connect to the broker through the MQTT command...
Hi,
I'm trying to compile Zigbee examples nRF5-SDK-for-Thread-and-Zigbee in Keil but faced some errors.
This is the error I got. This is the exact location of the project...
Hello,
I'm designing a device based on nRF52840 SoC that receives a configuration (set of 50 parameters) from an app which downloads the configuration in JSON format from...
Hi, I tried to run an adc example ( https://github.com/haakonsh/NCS_SAADC_example/tree/master . ) for nrf5340 in another post ( how-to-configure-the-dma-in-adc-and-how-to...
Hej!
Upgrading from SDK16.0.0 to SDK17.1.0, concerning sdk_config.h in my application: I worry that some new options could have been introduced while some old ones might...
Dear support,
I tried to follow the video here for adding service to https://webinars.nordicsemi.com/developing-bluetooth-low-energy-6 ,
Read and notification works fine...
I think I may have found errata. Using the combination in the title I can enable output, verified at the pin using OUTSET. Once the softdevice is enabled the same command...
