Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I have been using nRF Connect for Desktop and the Toolchain Manager with VC Studio for a couple of months on my Windows 10 machine for Zigbee development with the nRF52840...
Dear Nordic experts, This short code snippet is supposed to reset (unprovision) a Bluetooth Mesh node and reboot it (nRF5 SDK for Mesh 5.0.0): node_reset() is called at the...
Have a NCS/ZBoss-based Zigbee app running and I want to enable FOTA, and it was failing with missing app_update.bin file.
Thinking it might be something with my own code...
Hello All,
Maybe someone out there has done this - but is it AOK to swap +/- on the nRF52840 output so a -3.3V PWM signal can be generated?
Are there output zeners on...
I made an experiment with configuring the VSCode IDE for nRF development. The results were quite satisfactory so I decided to post an example configuration to github in case...
Unfortunately it is only ever explained here how printf is possible via UART. I wonder how printf is possible over BLE. I would like to send messages (strings) with numerical...
Hello, we have a goal of getting the BLE MAC address from out NRF52840 devices during manufacturing and printing it externally on the device. I was hoping the the MAC readout...
Hi,
We're having a problem that our application will hang when using the 32 kHz RC oscillator in the mcuboot bootloader and the Zephyr application. We encountered this...
Hello everyone,
I was wanting to perform FOTA on the nRF9160 DK, so I decided to implement the Application_Update example, I uploaded the app_update.bin binary to our...
I have an application where I need to count clock cycles on a GPIO input. I'm configuring a GPIOTE channel N to generate an IN EVENT on rising edge of an input GPIO PIN (the...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now it needs to add a function for deleting a "child node...
Hi,
I'm trying to set NFC pins as GPIO in my custom project. I'm using zephyr 1.8.0 SDK. I added the following line to my prj.conf:
CONFIG_NFCT_PINS_AS_GPIOS = y
...
Hi,
So I'm working on modifying the light switch example to send a larger payload on button press than just the boolean on_off value that's normally sent. I followed this...
