Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello everybody,
I am working on a nRF52832 DK and implemented libuarte (on a nRF52832) to communicate with another uC on said board. I am using sdk 17.0.2. The goal is...
Hi.
I want to write an app for nRF Connect for Desktop, where i keep track of the RSSI of a specific device and plot in into a chart. I thougt about reusing some parts of...
Hi,
I would like to use MCK as a clock for adc CLK 4Mhz.
Could i enable & configure all registers without I2S or PDM peripheral activation?
Is there a sample code for...
we have an app where we use a nRF52-DK board (with the 52832 chip) as a serial to BLE interface. We connect to the board using the USB UART channel. The interface IC on the...
In NCS@ sdk_nrf/subsys/bluetooth/gatt_dm.c: bt_gatt_dm_start():
if bt_gatt_discover() return with an error, the variable "dm" shall be release by calling "svc_attr_memory_release...
Hi,
I followed the structure of ble_app_uart__saadc_timer_driven__scan_mode project and customize a program on the nRF52805. I transmit data through BLE to Nordic uart service...
I get build error "undefined reference to `bt_mesh_sensor_apparent_energy32'" if I try to add this sensor type.
Rest of my sensors are included but this one not (e.g. bt_mesh_sensor_apparent_power...
I'm trying toa custom nRF52840 board using SDK 17.02 and SD 7.01
I create a read/Write only service, it shows up in nRF Connect just fine
I can write to the service using...
Good day,
1. I am running the Asset Tracker v2 app on my nRF9160DK and I am monitoring the battery voltage and its time stamp from my nRF9160DK, as this data is transmitted...
In the Matter documentation, under the topic Building Matter - > Getting Help , the "Also see the quick start guide" link is broken. For me it gives:
NOT_FOUND: Requested...
Hello,
I am trying to use googleapis.com to perform cell and wifi geolocation and am having trouble connecting.
I am using a custom board with a nRF9160 chip and the 1...
In the below picture, it says Thingy 91 is certified for the bands given below.
Can you please confirm if this board is certified for AT&T , Verizon?
Regards ...
Hi, am I able to communicate over mesh with long range (coded phy) and simultaneously communicate over GATT (say to Android phone) using 1M phy? If so, could you point me...
Hi,
We are switching from vanilla zephyr to NCS and would like some directions about support for zephyr LTS2. Can we expect Nordic to keep patches to NCS 1.8.x tracking...
