I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Hi Devzone,
I've been trying to verify and validate the performance of Instaburst mesh packets against regular ones. I modified a build of the mesh light switch example...
Hello,
I have been trying to get the thingy:91 up for 3 weeks or more now from Sri Lanka. I have made a lot of progress in getting data connectivity via MQTT to thethings...
`Hi There,
For nRF52840 board, If I want to fully disable JTAG or SWD lines after flashing, then what are the options to achieve it.
Questions:
1) If I want to disable...
My use case: There are different but similar peripherals advertising with 1M uncoded or coded PHY. Some of them are even advertising in mixed mode.
Question: How to connect...
Hello all,
I hope you are well. I am currently developing a product on the nrf52810 platform. I have a custom board and now have the BLE functional on the board. The next...
Good Day.
I want to measure the approximate voltage level on the battery in the nrf52820 microcontroller using a comparator (COMP) operating in Single-ended mode. I use...
am following the introductory videos and have done a fresh install of the Toolchain, Segger, VS Connect 3.7.2, nRF Connect SDK v1.8.0 and VS code on macOS
1. Installation...
Hi team,
I'm currently playing around with the sensor server example where I wanted to include the generic_onoff model in a separate element. I wanted to learn how to add...
Sure, my question is very stupid, but after one day I found nothing to explain the principle of the situation, I decided to ask.
I have a laptop with built-in Bluetooth...
Hi all,
I am trying to interface IS25LQ040B serial flash(512KB) IC with nrf52833 (bl653_dvk).
programmed sample code from "zephyr\samples\drivers\spi_flash"
I am getting...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
Hi,
I want to use the 64MHz crystal oscillator (HFXO) as the source for HFCLK clock controller. How can I need to enable or disable the item in KConfig on nRF Connect SDK...
Hi,
My project has a requirement to toggle the GPIO output in 400 to 500 microseconds cycle, I've tried to use the Timer on Zephyr but it can't supply a stable cycle in...
Is there a current example for nRF52840 power management under Zephyr / nRF Connect SDK?
Searches for this turn up old examples, such as this one , that are no longer in...
