My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi,
I am in the process in getting the AWS version of the Asset Tracker v2 on my Thingy:91. I was having some issues with getting the cerificate but was able to get that...
I can not get the SPI Slave function working on nRF52840 (nrf52840dk_nrf52840 board). My goal is to have spi0 as master and spi1 as slave.
By linking the MISO en MOSI lines...
Hi,
On the nRF5340-DK, i'm succesfuly using the example code:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_uart/README...
I'm working on the 9160 SoC using nRF Connect SDK 1.8.0 to send MQTT messages to an AWS endpoint. The messages correctly are able to send and the device works for 5-10 minutes...
Using NordicSDK 1.6.1 and the following in the bt_le_adv_param and relevant settings in prj.conf
The secondary advertising data packet contains the advertiser address...
Hi all,
I am now using nrf52840DK and llpm example in nrf connect sdk 1.7.1.
Now I have three nrf52840DK, one as master ,and the others are slaves, they both use Latency...
Hello!
We are planning on using the nRF52832 DK together with an external antenna. We are highly interested in the readings being as accurate as possible, and we are wondering...
We are developing an application in which we need to modify an existing device driver. It's about LIS2DH driver that is part of nRF Connect SDK v1.8.0 and we are using VSCode...
Hi, we are using the nRF52 DK (nRF52832) to read data from the i2s bus and store it as a wave-file on the connected SD-Card. When pressing button 1 on the DK, recording starts...
(For some reason, I use "...' replace the original string) Here is the log for using AT to do HTTPS POST:
2022-02-07T12:19:39.057Z DEBUG modem >> AT#XHTTPCCON=1,"...",443...
Hi,
I'm working with NRF Connect SDK, and once in a while when I add new configuration options to the prj.conf, I get an error that some region overflowed by X bytes,...
Dear friend,
Since the customized nRF5340 board does not have an external 32.768KHz low-frequency crystal oscillator, the following is added to prj.conf in netboot:
The...
Hi
This is the first time I have tried to use the nrf52840 dongle and the programmer v2.3.1, it can see the dongle( com10), but as soon as I select Device tis is the response...
